EQUIPMENT FOR SUBSTATIONS - Safety valve with spring MIP Cuprija
|
- product description
- company profile
product description
Description::Safety valve with a spring is an automatic device that without the aid of external energy except the energy of the working fluid, emits a certain amount of the same so that prevents exceeding a pre-determined pressure. It is used in power plants for the production of hot and cold water.
The construction of safety valve with spring
The operational requirements arising from the needs of the market to create a reliable valve with the ability to express the maximum flow rate at the outlet of the valve at low values of pressure at the entrance of the result of this construction. Increasing the length of the spring and ovećanim inlet below the shutter enabled the huge KVS-value valve with the local pressure drop d 8-10 bar. Repository tandem spring closed, so canned springs have the opportunity being lost performance during operation. Tightening the spring goes through the thrust bearing and the block is a special nut. Raising the locking body of seats in use is possible via a special eccentric and lever located on the exterior design of the valve.
Material for safety valve with spring
The valve body, the body and the valve cover is made of steel. Valve seat and the locking body, spindle and two-piece ring made of Prohron. Sliding support spindles are made of bronze. Dihtujući prebunama or parts of silicone depending on the temperature.
Setting the safety valve with spring
Safety valve spring on the request of the customer sets in the organization. Each valve spring delivers a certificate of labor organization in which they are registered properties springs, embedded material, calibrated sizes and nominal diameter.
The construction of safety valve with spring
The operational requirements arising from the needs of the market to create a reliable valve with the ability to express the maximum flow rate at the outlet of the valve at low values of pressure at the entrance of the result of this construction. Increasing the length of the spring and ovećanim inlet below the shutter enabled the huge KVS-value valve with the local pressure drop d 8-10 bar. Repository tandem spring closed, so canned springs have the opportunity being lost performance during operation. Tightening the spring goes through the thrust bearing and the block is a special nut. Raising the locking body of seats in use is possible via a special eccentric and lever located on the exterior design of the valve.
Material for safety valve with spring
The valve body, the body and the valve cover is made of steel. Valve seat and the locking body, spindle and two-piece ring made of Prohron. Sliding support spindles are made of bronze. Dihtujući prebunama or parts of silicone depending on the temperature.
Setting the safety valve with spring
Safety valve spring on the request of the customer sets in the organization. Each valve spring delivers a certificate of labor organization in which they are registered properties springs, embedded material, calibrated sizes and nominal diameter.
Availability:Contact
Company:Expont d.o.o
company profile
Expont d.o.o
- Company introduction:Expont d.o.o je trgovinsko preduzeće iz Beograda specijalizovano za promet opreme za grejanje i vodovod, osnovano 1992 godine. Nalazimo se u ulici Vojvode Stepe 153, na placu od 1100 m2, i halom od 250 m2. Pored maloprodaje u ulici Kumodraska 55 imamo još četiri maloprodaje. U sastavu privrednog društva Expont je proizvodno preduzeće Mip Livnica iz Ćuprije osnovano 1970. godine. Mip Livnica kao deo Exponta je jedini srpski proizvođač armature od sivog liva. Pored starog proizvodnog programa koji obuhvata odbojne klapne, hvatače nečistoće, kondenz lonce, usisne korpe i sl. sa 87 zaposlenih Mip danas lije i proizvodi ravno zaporne ventile, nepovratne ventile, leptir ventile, ventile sigurnosti sa tegom i oprugom, dvodelne loptaste slavine, prirubnice i ostalu prirubničku armaturu za podstanice. Preduzeće Expont preko svoje veleprodaje snabdeva trgovine, više od 700 izvođačkih firmi, od toplotne podstanice, primara i sekundara, preko cevnog razvoda pa sve do kućnih instalacija grejanja i vodovoda. Roba se isporučuje uz validan atest i garanciju, u šta su se uverile JKP Beogradske, Novosadske i ostale toplane, TE Kolubara, Kostolac i Obrenovac. Naš prioritet su mnogobrojni izvođači termo-tehničkih i vodovodnih instalacija , uz koje se preduzeće Expont razvilo, i napredovalo na srpskom tržištu. Za dugogodišnje saradnike kao i nove a korektne saradnike naše preduzeće je uvek spremno da u najkraćem roku, uz dobre cene kao i posebne rabatne skale dopremi opremu na gradilište.
- Contact Person Name:Goran Razumenić
- Address:Vojvode Stepe br. 153
- Post Code:11000
- city:Beograd , Serbia
- Cell Phone #:+381 60 641 68 32
- Telephone #:+381 11 398 20 22
- Fax #:www.expont.rs
- Geo Location:Show
